超高强韧油井管合金设计与高强韧机制

 为了揭示1 000 MPa级低碳加铌钒钛微合金钢的高强韧机制,研究了S1(w(C)=0.09%)与S2(w(C)=0.17%)两种合金成分的油井管钢成分-工艺-组织-性能关系。试验表明,两种成分试验钢经水淬后的组织分别为板条贝氏体加少量马氏体和马氏体加少量贝氏体的复相组织。两种成分钢经过450~600 ℃、30 min的中温回火后,组织中均出现碳化物析出,且S1试验钢回火后的屈服强度基本不变,抗拉强度下降了约70 MPa,S2试验钢回火后的屈服强度与抗拉强度迅速升高170 MPa左右。溶度积公式的计算结果表明,两种钢的水淬组织中铌、钛元素析出彻底且析出物的体积分数都很小,因此回火铁素体基体中的VC析出强化对S1试验钢回火后屈服强度保持不变以及S2试验钢回火后屈服、抗拉强度提高起到重要作用。     

钢铁生产的水能关系分析

从钢铁生产过程中水资源使用时的能耗角度研究了钢铁联合企业的水能关系，提出了水能强度的概念来评价企业生产过程中水资源利用的节能水平，建立了钢铁企业的水能关系模型。以中国某大型钢铁联合企业为例，计算并分析了该企业的水能关系。该企业总的水能量为55 709 kW·h/h，重复用水水能量占整个钢铁企业全部水能量的82%，补水水能量占16%，排水水能量占1%；各工序中热轧工序占比最大，其次是炼铁、炼钢工序，冷轧、烧结和炼焦工序较低。该企业的吨钢水能强度为0.208 kW·h/m3，炼铁工序的水能强度最高，热轧、炼钢工序次之，烧结、冷轧和炼焦工序较低。最后，从钢铁生产过程水资源利用的角度得到节能的方向及措施。     

Synthesis of the Antibiotic Precursor Thiazolyl‐7‐Aminocephalosporanic Acid in a Microstructured Flow System

The synthesis of thiazolyl‐7‐aminocephalosporanic acid, a pharmaceutical precursor of the β‐lactam antibiotic drug cefodizime, could be successfully realized in a continuous microstructured flow system. This was accomplished by changing the process window from batch, having a reaction temperature of 60 °C with a reaction time of 1 h, to a flow system at temperatures > 100 °C and reaction times of several minutes. The space‐time yield could be increased by a factor of 130.     

橙皮苷酶解液中橙皮素单糖苷的树脂分离

橙皮苷酶解液组分复杂，含糖类、橙皮素和橙皮素单糖苷（hesperetin-7-O-glucoside，HMG）等。采用了6种大孔吸附树脂和半制备液相色谱分离纯化橙皮苷酶解液中的HMG，并通过红外、紫外和XRD手段表征产物结构，同时采用羟基自由基清除试验探讨其抗氧化活性。结果表明：HPD300大孔树脂最适于酶解液中HMG的分离；HPD300大孔树脂对酶解液中主要组分的静态和动态总吸附量分别为48.35 mg/g和35.82 mg/g，主要用于分离糖类杂质；以10 BV的45%乙醇为洗脱剂，洗脱流速1.2 mL/min，洗提物中HMG纯度从80.37%提高到97.83%；洗提物经半制备液相进一步分离纯化后得到单体HMG，最终纯度可达98.21%, 经紫外、红外和XRD手段验证产物为HMG；且HMG的羟基自由基清除能力略高于橙皮素，远高于橙皮苷。     

不锈钢酸洗污泥对烧结黏结相与平衡相的影响

 不锈钢酸洗污泥安全填埋占用土地且难以消除对环境的危害，将酸洗污泥作为烧结配料使用有望回收其中铁、铬、镍等金属，并充分利用其中的熔剂组分，实现酸洗污泥在冶金企业的闭路资源化利用。铁矿粉配加酸洗污泥烧结黏结相强度试验表明，随着酸洗污泥配加比例的增加，黏结相强度先增加后减小，且随着碱度的增加整体减小，当酸洗污泥配加比例为10%时，试样中赤铁矿、磁铁矿质量分数最大，枪晶石质量分数较小，在碱度为1.5时于1 280 ℃焙烧4 min，试样的黏结相强度最大可达15.12 kN。平衡相烧结试验表明，配加酸洗污泥能改善烧结矿质量，铁矿粉配加10%的酸洗污泥，碱度为1.5，1 300 ℃烧结240 min后，烧结矿的矿相组成和微观结构最好，综合性能最佳。     

Heat propagation in thermally conductive polymers of PA6 and hexagonal boron nitride

Thermally conductive polymers offer new possibilities for the heat dissipation in electric and electronic components, for example, by a three‐dimensional shaping of the heat sinks. To face safety regulations, improved fire performance of those components is required. In contrast to unfilled polymers, those materials exhibit an entirely different thermal behavior. To investigate the flammability, a phosphorus flame retardant was incorporated into thermally conductive composites of polyamide 6 and hexagonal boron nitride. The flame retardant decreased the thermal conductivity only slightly. However, the burning behavior changed significantly, due to a different heat propagation, which was investigated using a thermographic camera. An optimum content of hexagonal boron nitride for a sufficient thermal conductivity and fire performance was found between 20 and 30 vol%. The improvement of the fire performance was due to a faster heat release out of the pyrolysis zone and an earlier decomposition of the flame retardant. For higher contents of hexagonal boron nitride, the heat was spread faster within the part, promoting an earlier ignition and increasing the decomposition rate of the flame retardant.     

Electromagnetic torque detecting for optimization of in-mould electromagnetic stirring in the billet and bloom continuous casting

ABSTRACT

In this paper, an electromagnetic torque device based on the theoretical model was established to determine the optimum frequency accurately and conveniently in billet and bloom continuous casting with in-mould electromagnetic stirring (M-EMS). Magnetic characteristics with M-EMS was investigated by numerical simulation and physical experiment with the application of electromagnetic torque device and gauss meter. In addition, the effects of stirring frequency with M-EMS on macro segregation and equiaxed crystal ratio were compared and analysed for 55SiCr with 150?mm?×?150?mm billet caster and BU with 310?×?360?mm bloom caster by a series of plant trials, respectively. The results showed that maximum magnetic flux density and maximum electromagnetic torque occurred with different frequency and same current in M-EMS, and central equiaxed crystal ratio and macro segregation has been significantly improved by optimum frequency with M-EMS.